The 5 Best Bathtub Grab Bars and Tub Rails in 2026
One screw-in bar for the tub wall and four clamp-on rails for the tub’s edge, rated from 250 to 500 lbs.
If you can drill into the wall beside your tub, put a 24 inch bar there: Moen rates its R8724P at 500 lbs when the screws go into a stud or Moen’s SecureMount anchors. If you rent, or the tile can’t be drilled, clamp the Drive Medical adjustable rail onto the tub’s edge. Drive rates it at 300 lbs and says it fits tub walls 3 to 7 inches thick.
Our Picks at a Glance
| Bar or Rail | Price | Capacity | Mount | Fits | Best For |
|---|---|---|---|---|---|
| Moen 24″ Peened Grab Bar (R8724P) Moen 24″ Grab Bar on Amazon: $28.85 |
$28.85 | 500 lbs (stud or Moen anchors) | Screws into the wall | Any wall with a stud or Moen anchors | A permanent bar you can drill for |
| Drive Medical Adjustable Tub Rail (RTL12036-ADJ) Drive Adjustable Tub Rail on Amazon: $32.88 |
$32.88 | 300 lbs | Clamp, no tools | Tub walls 3″ to 7″ | Renters and most tubs |
| Moen SecureLock Tub Grip (DN7175) Moen SecureLock Tub Grip on Amazon: $56.50 |
$56.50 | Users under 350 lbs | Clamp, no tools | Tub walls 2.75″ to 5.5″ (retailer figure) | A heavier user who can’t drill |
| Vaunn Adjustable Bathtub Rail Vaunn Adjustable Tub Rail on Amazon: $39.99 |
$39.99 | 300 lbs (retailer figure) | Clamp, no tools | Flat, rigid tub walls 3″ to 7″ (listing); not fiberglass | A taller user |
| Carex Dual Level Bathtub Rail (FGB20300) Carex Dual Level Tub Rail on Amazon: $62.41 |
$62.41 | 250 lbs | Spring clamp, no tools | Flat-top tub walls (range not published) | Sitting down into the bath |
You can hold on at a bathtub in two ways. A bar screwed to the wall beside the tub stays put and carries the most weight, but it needs a stud or proper anchors behind the tile. A clamp-on rail grips the tub’s own side wall and gives you an upright handle right where you step over. It goes on without tools and comes off when you move, and every clamp-on rail here carries a lower rating than the stud-mounted bar.
The CDC found that 68.3 percent of nonfatal bathroom injuries among people 15 and older in 2008 happened in or around the tub or shower, with injury rates rising with age (MMWR, June 10, 2011). The same report recommends grab bars in and around the tub.
Every clamp-on rail grips the tub’s side wall, so measure how thick that wall is across the top and check that the top is flat. Vaunn’s listing says its rail is not for fiberglass, curved, angled or textured tub walls. Drive says to tighten its rail carefully on fiberglass. A clamp holds by pressure on the tub wall, so check that it’s still tight before you put weight on it.
Moen Home Care 24″ Peened Grab Bar (R8724P)
Moen rates this bar at 500 lbs, the highest rating in this guide, and it costs the least of the five. You need a drill and a stud, or Moen’s SecureMount anchors, to get that rating.
500 lbs into a stud or SecureMount anchors
24″
1.25″
304 stainless steel, peened grip
Screws into a stud; anchors sold separately
Moen Limited Lifetime
4.8 / 5 (safety specs 5, fit 4, warranty 5, value 5)
At 24 inches, this bar matches the minimum length the 2010 ADA Standards set for the back-wall and control-end bars at a public bathtub (section 607.4). Its 1.25 inch diameter sits inside the ADA’s 1.25 to 2 inch range. A home doesn’t have to follow those rules; the placement section below gives their measurements.
Moen calls the peened finish, a dimpled texture in the steel itself, slip-resistant. Moen also says its SecureMount design lets the concealed screws go into a stud at any angle, so the bar can run horizontal along the back wall or vertical at the tub’s entry. Where there’s no stud, Moen sells SecureMount anchors separately.
What to Know Before Buying
The 500 lb rating holds only when the screws reach a stud or Moen’s SecureMount anchors, which are sold separately. Moen’s rating names only those two mountings, so it doesn’t cover other wall anchors. If you rent, ask your landlord first, or pick one of the clamp-on rails below.
Drive Medical Adjustable Clamp-On Tub Rail (RTL12036-ADJ)
Without a drill, we’d start here. It’s the least expensive clamp-on in this guide, Drive puts the 300 lb rating on its own spec sheet, and the clamp opens from 3 to 7 inches.
300 lbs
3″ to 7″
14.5″ to 17″ (Drive figure)
Powder-coated steel, stainless lock
7 lbs
Limited Lifetime
4.5 / 5 (safety specs 4, fit 4, warranty 5, value 5)
The rail tightens onto the tub wall with a stainless steel locking mechanism, and Drive says its rubber pads won’t scratch the tub. Drive’s spec sheet gives the clamp range as 3 to 7 inches and the height adjustment as 14.5 to 17 inches. Drive’s fixed 12036 rail is the same design without the height adjustment, set at 14.5 inches.
Drive covers it with a limited lifetime warranty. It also lists a Medicare billing code for it, E0246. A code tells a supplier how to bill, but it doesn’t mean Original Medicare pays (see the FAQ).
What to Know Before Buying
The Amazon listing gives the height range as 14 to 17 inches and doesn’t state a weight capacity. We use Drive’s figures: 14.5 to 17 inches and 300 lbs. Drive’s only note on tub material is to tighten the rail carefully on a fiberglass tub.
Moen SecureLock Tub Grip (DN7175)
For a user over 300 lbs who can’t drill, it’s the only clamp-on here rated above 300 lbs. Moen’s instructions limit it to people weighing less than 350 pounds, 50 more than the next rail.
Users under 350 lbs
2.75″ to 5.5″ (retailer figure)
Polypropylene, rubber pads
Locking clamp
Not stated by Moen (Amazon listing says limited lifetime)
2.9 / 5 (safety specs 3, fit 3, warranty 2, value 3.5)
The instruction sheet that ships with the DN7175 reads “for use only by persons weighing less than 350 pounds,” and the Amazon listing gives the same 350. The grip is molded polypropylene with rubber pads where it meets the tub, and a lock holds the clamp once it’s tightened.
It costs roughly 70 percent more than the Drive rail. The extra money buys the 50 lb margin and nothing else we can document, so a user well under 300 lbs is better served by the Drive.
What to Know Before Buying
Moen doesn’t publish the range of tub-wall thicknesses this grip fits. The 2.75 to 5.5 inch range comes from the plumbing supplier F.W. Webb, and it tops out narrower than the Drive and Vaunn clamps, so measure a thick or tiled tub ledge first. Moen’s instructions don’t say which tub materials it suits, and they state no warranty. The Amazon listing, sold by Amazon, lists a limited lifetime warranty, but we couldn’t tie that to Moen, so the warranty scores 2. It scores near the bottom despite the highest clamp-on rating because neither the clamp range nor the warranty comes from Moen.
Vaunn Adjustable Bathtub Rail
Its Amazon listing gives a handle height of 17 to 20 inches, three inches taller at the top than the Drive, and no other rail here publishes a taller one. Pick it for a tall user with a flat, rigid tub wall.
300 lbs (listings)
3″ to 7″ (listing)
17″ to 20″ (listing)
Powder-coated stainless steel, foam grip (listing)
Under 6 lbs (listing)
3.1 / 5 (safety specs 3, fit 3, warranty 2, value 4.5)
The listing describes a padded rubber clamp that locks onto the tub wall and a vertical handle with a foam grip. Carex and Moen don’t publish grip heights, so this is the tallest handle we can document.
What to Know Before Buying
Vaunn’s Amazon listing, sold by a third-party seller, says the rail is not made for fiberglass, curved, angled or textured tub walls, and gives the 3 to 7 inch clamp range. We found no Vaunn spec sheet, so the 300 lb rating rests on listings alone, and we found no published warranty.
Carex Dual Level Bathtub Rail (FGB20300)
The only rail here with two grips: a high one to hold while you step over and a low one to push on as you lower yourself into the water or stand back up. It also has the lowest rating, 250 lbs, and costs the most of the clamp-ons.
250 lbs
Two levels, textured
Adjustable steel spring clamps, rubber-lined
Flat-top tub walls; range not published
Chrome (listing)
2.6 / 5 (safety specs 2, fit 3, warranty 2, value 3.5)
Carex is now a Drive Medical brand, and Drive’s Carex product page rates this rail at 250 lbs, matching the Amazon listing. The Amazon listing describes rubber-lined steel spring clamps that go on without tools.
Choose it when sitting down into the water and getting back up is where the bather needs help, and the bather weighs well under 250 lbs. For stepping over the wall alone, the Drive rail carries 50 lbs more for about half the price.
What to Know Before Buying
Neither Carex nor the Amazon listing gives the range of wall thicknesses the clamp fits or the height of each grip, and we found no published warranty. The listing says only that it fits most tubs with a flat-top wall. Without a published clamp range, its safety-specs score is 2. Ask the seller for the range before you order if your tub wall is unusually thick or thin.
Where to Put Grab Bars at a Bathtub
No law sets grab bar positions in a private home. The 2010 ADA Standards apply to public and commercial buildings, and section 607.4 gives the layout they require for a bathtub with no built-in seat:
- Two horizontal bars on the back wall, the long wall the tub runs along, each at least 24 inches long. One goes 33 to 36 inches above the bathroom floor, measured to the top of the bar (section 609.4). The other goes 8 to 10 inches above the tub rim.
- A bar at least 24 inches long on the control end wall, where the faucet is, at the front edge of the tub.
- A bar at least 12 inches long on the head end wall, opposite the faucet, at the front edge of the tub.
The same standards require round bars from 1.25 to 2 inches across (section 609.2.1) and a mounting that holds a 250 pound force at any point (section 609.8). The ADA describes wall-mounted bars only; a clamp-on rail is a separate product that the standards don’t address. You can use both: a clamp-on rail at the spot where you step over, and a wall bar to hold once you’re standing in the tub.
If You Sit Down to Bathe
For lowering yourself into the water, look at the lower back-wall bar, which the ADA sets 8 to 10 inches above the rim, or the Carex rail’s low grip. If you can’t safely step over the wall at all, a tub transfer bench lets you sit down outside the tub and slide across; our guide to tub transfer benches compares four.
Find the studs behind the tub’s back wall with a magnetic stud finder and mark both ends of the bar before you drill. If the spot you want falls between studs, Moen’s SecureMount anchors let the bar stay where you’ll reach for it.
Related Guides
For bars in a walk-in shower, beside the toilet or by the bed, see our guide to the best grab bars for showers. If a suction-cup bar is on your tub wall now, read Are Suction Cup Grab Bars Safe? before you lean on it.
How We Evaluated These Bars and Rails
We checked each weight rating, clamp range and warranty against the maker’s own documentation first: Drive’s spec sheet, Drive’s Carex product page, Moen’s DN7175 instruction sheet and Moen’s product information for the R8724P. Amazon listings came second, in November 2026. Where a figure came only from a retailer, the review says so. Where the maker and a listing disagree, we use the maker’s figure, except for weight capacity, where we use the lower of the two.
We don’t have physical samples of these products and didn’t test them. Descriptions of how each one mounts come from the maker’s documentation, or from the Amazon listing where the review says so.
The comparison table and buttons show the prices we saw on Amazon in November 2026.
How we score: We rate each pick from 1 to 5 on four criteria and average them. Safety specs is how fully the maker documents the weight rating and, for a clamp-on rail, the clamp range, and whether the Amazon listing agrees. Fit is how well the pick suits a handhold at a standard bathtub. Warranty is the maker’s stated terms, and a pick with no published warranty scores low. Value is price against features, compared only with the other picks here. Scores come from published specs, warranty terms and prices, not hands-on testing. A figure the maker publishes, including on the maker’s own Amazon store, counts as maker documentation. A pick can be the best fit for one need and still score lower overall.
Frequently Asked Questions
Are clamp-on tub rails safe?
Only on a tub wall the clamp fits and the maker allows. The clamp-on rails here are rated from 250 to 350 lbs, against 500 lbs for the stud-mounted Moen bar. Check the wall thickness and material against the maker’s limits first.
Can I put a clamp-on rail on a fiberglass tub?
It depends on the rail. Vaunn’s listing says its rail is not for fiberglass. Drive doesn’t rule out fiberglass; it says to tighten its rail carefully on a fiberglass tub. Moen’s instructions and Drive’s Carex product page don’t address tub material, so ask the seller before using either on fiberglass.
How high should a grab bar be above a bathtub?
The 2010 ADA Standards, which apply to public buildings, put one back-wall bar 33 to 36 inches above the floor and a second bar 8 to 10 inches above the tub rim (sections 607.4 and 609.4). No rule applies in a private home, so set the bars for the height of the person using the tub.
Does Medicare pay for bathtub grab bars or tub rails?
Usually not under Original Medicare, but check with your provider. Medicare’s national coverage list for medical equipment denies grab bars as a “self-help device; not primarily medical in nature” (CMS NCD 280.1). Tub rails aren’t named in that list. Drive lists billing code E0246 for its rail, but a code doesn’t mean Medicare pays. Some Medicare Advantage plans may offer a bathroom safety benefit, so ask your plan before you buy.