The 5 Best Threshold Ramps in 2026
Rubber and aluminum ramps for doorway lips, raised landings and rises up to about 6 inches, with the slope each one creates.
Our Picks at a Glance
Jump to the full review of any ramp below.
| Ramp | Price | Capacity | Rise (size shown) | Length x Width | Slope | Material |
|---|---|---|---|---|---|---|
| EZ-ACCESS Angled Entry Mat, 1-1/2″ EZ-ACCESS Entry Mat on Amazon: $116.52 |
$116.52 | 850 lbs | 1-1/2″ | 14″ x 36-1/16″ usable | About 1:9 | Recycled rubber |
| Silver Spring Solid Rubber, 1″ Silver Spring 1″ Rubber Ramp on Amazon: $39.99 |
$39.99 | 1,500 lbs | 1″ | 8″ x 43-1/2″ | 1:8 | Recycled rubber |
| Silver Spring Rubber 3-Channel, 4″ Silver Spring 4″ 3-Channel Ramp on Amazon: $119.99 |
$119.99 | 600 lbs | 4″ | 24″ x 42″ | 1:6 | Rubber |
| EZ-ACCESS Modular Entry Ramp, 3″ EZ-ACCESS Modular Ramp on Amazon: $92.62 |
$92.62 | 700 lbs | 2.75″ to 3.25″ | 16.64″ x 34″ usable | About 1:6 to 1:5 | Aluminum |
| EZ-ACCESS Angled Entry Ramp, 36″ EZ-ACCESS Angled Entry Ramp on Amazon: $194.99 |
$194.99 | 700 lbs | 3-5/8″ to 5-7/8″ | 35-7/8″ x 36-1/4″ | About 1:10 to 1:6 (overall length) | Aluminum |
A threshold ramp bridges a small, abrupt rise: the lip of an exterior door, a sliding-door track, a sunken living room, a step down to a garage. The five here run from 8 to 36 inches long, and most are meant to stay in place at one doorway. For a wheelchair, scooter or rollator, it turns a bump that stops a front caster into a short incline.
A short ramp over a fixed rise makes a steep slope. A 1 inch rise over an 8 inch rubber ramp is 1:8, steeper than the 1:12 maximum for public ramps, and every pick below lists its slope so you can compare.
Measure the rise before you shop. Lay a level or a straight board flat on the higher surface so it sticks out over the lower one, then measure straight down from the bottom of the board to the floor. Do this at both ends of the doorway and use the higher number. If it falls between two sizes, check each size’s stated height range; a ramp taller than the lip leaves its top edge as a new bump.
The 2010 ADA Standards apply to public and commercial buildings. There, a change in level up to 1/4 inch needs no treatment, up to 1/2 inch is allowed if beveled no steeper than 1:2, and anything above 1/2 inch must be treated as a ramp, with a maximum running slope of 1:12 (U.S. Access Board). The ADA doesn’t cover a ramp at a private home; the ADA’s 1:12 is still a useful benchmark. Every ramp in this guide is steeper than 1:12. Check your wheelchair or scooter manual for the steepest slope its maker allows.
EZ-ACCESS TRANSITIONS Angled Entry Mat
Quarter-inch size steps let you buy the height of your door lip, for any lip from 1/2 inch to 2-1/2 inches.
850 lbs (all sizes)
1/2″ to 2-1/2″, in 1/4″ steps
14″ L x 36-1/16″ W usable
18 lbs
Recycled rubber, made in USA
Can be trimmed or notched
About 1:9
Lifetime
4.4 / 5 (safety specs 5, fit 3, warranty 5, value 4.5)
EZ-ACCESS sells this mat in nine heights, from 1/2 inch to 2-1/2 inches in quarter-inch steps. A door lip that measures 1-3/4 inches gets a 1-3/4 inch ramp, for a closer fit at the top edge. EZ-ACCESS rates every size at 850 lbs.
The rubber can be trimmed or notched, according to EZ-ACCESS, so the mat can fit around a door jamb, a weatherstrip or a storm-door frame. The 1-1/2 inch model gives 36-1/16 inches of usable width, and the mat weighs 18 lbs. EZ-ACCESS backs it with a lifetime warranty.
Who Should Buy This
Buy it if your doorway rise is between 1/2 inch and 2-1/2 inches and you want one ramp to leave in place for years.
What to Know Before Buying
The mat tops out at 2-1/2 inches; above that, look at the aluminum picks below. Weight climbs with height, from 2 lbs at 1/2 inch to 49 lbs at 2-1/2 inches, so the taller sizes are not easy to move between doors. Amazon carries two listings for the black 1-1/2 inch size at different prices; check that the rise in the title matches your measurement before you order.
Silver Spring Solid Rubber Threshold Ramp
The least expensive ramp here, with the highest weight rating, 1,500 lbs.
1,500 lbs
1/2″ to 2-1/2″
8″ L x 43-1/2″ W
11 lbs
Recycled rubber
Grooved, with drain channels
1:8
One year
4.0 / 5 (safety specs 5, fit 3, warranty 3, value 5)
Silver Spring, the house brand of the retailer DiscountRamps, rates this solid rubber ramp at 1,500 lbs on its product page, and the Amazon listing states the same figure. The 1 inch model is 8 inches long and 43-1/2 inches wide, the widest ramp here. Molded channels let rain drain off at an exterior door, and the sides are beveled.
It comes in rises from 1/2 inch to 2-1/2 inches, though with fewer steps than the EZ-ACCESS mat. The 2 inch size keeps the same 1:8 slope at 16 inches long.
Who Should Buy This
It fits a home with one or two low lips, such as an exterior door or a step into a bathroom, on a budget that does not stretch to the EZ-ACCESS mat.
What to Know Before Buying
The warranty is one year against EZ-ACCESS’s lifetime. Silver Spring does not say the rubber can be cut, so do not plan to trim it.
Silver Spring Rubber 3-Channel Threshold Ramp
Rubber that reaches a 4 inch rise, with three channels underneath so a garden hose or extension cord can pass under it.
600 lbs
2-1/2″, 3″, 4″
24″ L x 42″ W
57 lbs
Three channels for cords or hoses
Grooved rubber
1:6
One year
3.9 / 5 (safety specs 5, fit 3, warranty 3, value 4.5)
The two rubber picks above stop at 2-1/2 inches. This Silver Spring line comes in 2-1/2, 3 and 4 inch rises, each 24 inches long and 42 inches wide and rated at 600 lbs. The 4 inch size weighs 57 lbs.
The three channels on the bottom let a hose or a power cord run under the ramp instead of over it, at a garage step or a patio door.
Who Should Buy This
A rise between 2-1/2 and 4 inches where the ramp will stay in one place, especially where something has to pass underneath.
What to Know Before Buying
At 4 inches over 24 inches the slope is 1:6, the steepest of the rubber picks. We treat 1:12 as the steepest slope for independent use. Every ramp here is steeper than that at the top of its range, so check your wheelchair or scooter maker’s maximum safe incline before relying on one alone. The 2010 ADA Standards (Table 405.2) allow steeper slopes only in existing buildings with no room for a longer ramp, up to 1:10 for a rise of 6 inches or less and up to 1:8 for 3 inches or less, never steeper than 1:8, so 1:6 is steeper than the ADA allows anywhere. Check your wheelchair or scooter maker’s maximum safe incline. For a gentler slope at this height, a portable ramp of 4 feet or longer from our wheelchair ramp guide is the better choice. The 600 lb rating is lower than the two rubber picks above, and the warranty is one year. Silver Spring’s product page lists the 2-1/2 inch model at 31 lbs in one place and “50 lbs. or less” in another.
EZ-ACCESS TRANSITIONS Modular Entry Ramp
The lightest aluminum ramp here, 8 lbs at the 3 inch size, built from sections so one ramp can be reset for a lower door.
700 lbs (all sizes)
1″ to 6″ rise
16.64″ L x 34″ W usable, with flap
2.75″ to 3.25″
8 lbs
Aluminum, extruded slip-resistant surface
About 1:6 to 1:5
Lifetime
4.4 / 5 (safety specs 5, fit 3, warranty 5, value 4.5)
The modular ramp is built from aluminum sections that hook together with the included screws. Removing a section lowers it, according to EZ-ACCESS, so one ramp can be reset for a lower door. The 3 inch model itself covers 2.75 to 3.25 inches. EZ-ACCESS rates every size at 700 lbs and covers it for life.
It has pre-drilled holes to anchor it to the floor. EZ-ACCESS does not include the anchoring hardware, so buy screws suited to your floor or threshold.
Who Should Buy This
It suits a doorway rise of 2.75 to 3.25 inches where you want a light aluminum ramp. If you later need it at a lower door, removing a section resets it. Once it has a permanent spot, the pre-drilled holes let you anchor it.
What to Know Before Buying
This is the steepest ramp here. A 3 inch rise over 16.64 inches works out to about 1:5.5, and at the 3.25 inch top of its range about 1:5.1. EZ-ACCESS tells buyers to follow their mobility device’s owner’s guide for acceptable slope. For a longer run at this height, the 24 inch size of the angled ramp below covers about 2-1/8 to 4-3/8 inches, depending on which feet you use. Assembly is required.
EZ-ACCESS TRANSITIONS Angled Entry Ramp
Adjustable swivel feet let it sit level on a sloped step or patio, and the 36 inch size is the longest ramp here, for the gentlest slope at 4 to 6 inches.
700 lbs (all sizes)
12″, 24″, 36″ long
35-7/8″ L x 36-1/4″ W overall
3-5/8″ to 5-7/8″
15.2 lbs
Swivel, adjust independently
About 1:10 to 1:6
Lifetime
4.1 / 5 (safety specs 4, fit 4, warranty 5, value 3.5)
A ramp with a fixed base needs a flat landing. If your stoop drains away from the house or one corner of the step sits higher, the Angled Entry Ramp stands on two swivel feet that adjust independently, so the top edge meets the threshold evenly on both sides.
The 36 inch model spans a rise of 3-5/8 to 5-7/8 inches with its 2-1/2 inch feet. At the low end of that range the slope is about 1:10, at the high end about 1:6. It weighs 15.2 lbs, comes with anchoring hardware for the bottom plate, and carries EZ-ACCESS’s lifetime warranty and 700 lb rating.
Who Should Buy This
A rise of roughly 4 to 6 inches at a step or sliding door where the ground is uneven, or anyone who wants the longest threshold ramp here before moving up to a full portable ramp.
What to Know Before Buying
It was the most expensive ramp here when we checked. EZ-ACCESS’s spec table and its own FAQ give slightly different rise ranges for each size; we use the spec table. For a rise over 6 inches, look at a portable ramp; our guide to choosing a wheelchair ramp length shows the length each step height needs.
How to Choose a Threshold Ramp
Match the Rise Exactly
A threshold ramp should meet the top of the lip flush. Too low and the wheel hits a ledge at the top; too tall and the ramp’s top edge becomes a new bump. Measure in two or three places across the doorway, since a sill can sit higher at one end, and buy for the highest point.
Rubber or Aluminum
The rubber ramps here weigh from 11 to 57 lbs in the sizes shown and stop at 4 inches. They suit a permanent spot at one door. The two aluminum ramps here weigh 8 and 15.2 lbs in the sizes shown, reach higher rises and can be moved between doors. Both aluminum picks here have anchor holes, and EZ-ACCESS includes hardware only with the Angled Entry Ramp.
Slope and Steepness
Divide the ramp’s length by the rise to get the slope: 8 inches over a 1 inch rise is 1:8. Every ramp here is steeper than the 1:12 target. We treat 1:12 as the steepest slope for independent use. Every ramp here is steeper than that at the top of its range, so check your wheelchair or scooter maker’s maximum safe incline before relying on one alone. The 2010 ADA Standards (Table 405.2) allow steeper slopes only in existing buildings with no room for a longer ramp, up to 1:10 for a rise of 6 inches or less and up to 1:8 for 3 inches or less, never steeper than 1:8. The ADA covers commercial and public buildings, not private homes, where it is a guide. Check your wheelchair, scooter or rollator maker’s maximum safe incline in its manual; EZ-ACCESS tells buyers to follow it.
Width
EZ-ACCESS lists usable width for its modular ramp (34 inches) and its mat (36-1/16 inches) and overall width for the angled ramp (36-1/4 inches). Silver Spring lists 42 inches for the 3-Channel ramp and 43-1/2 inches for the solid ramp. Measure the clear width of your doorway and the width of your wheelchair or scooter, and choose a ramp wider than the device’s overall width, with room to spare.
Before you anchor or trim anything, set the ramp in place and roll over it a few times with the wheelchair, scooter or rollator that will use it, with a helper beside you. If the front wheels bump at the top edge, the ramp may be the wrong size.
Related Guides
For a full step or more, our guide to portable wheelchair ramps covers folding ramps from 2 to 6 feet. Rollator users crossing thresholds every day may also want our outdoor rollator guide, which compares wheel sizes for bumps and curbs.
How We Evaluated These Ramps
We checked every specification against the manufacturer’s product page first and the Amazon listing second, in October 2026. Slopes are our own arithmetic from each maker’s published rise and length; where a maker gives only overall length, the sloped surface may be a little shorter and the true slope a little steeper. ADA facts come from the U.S. Access Board’s guide to the 2010 Standards and the Department of Justice’s Title III Technical Assistance Manual.
We do not have physical samples of these ramps and did not test them.
How we score: We rate each ramp on four criteria, each from 1 to 5, and average them. Safety specs is how fully the maker documents the weight rating and other safety figures. Fit is how well the ramp suits a doorway lip or raised landing up to about 6 inches. Warranty is the maker’s stated term. Value is the price against what the ramp offers, compared only with the other ramps in this guide. The scores come from published specs, warranty terms and prices; we did not test the ramps. When a listing and the maker disagree, or the maker gives two different safety figures, the safety specs score goes down. A figure the maker publishes, including on the maker’s own Amazon store, counts as maker documentation. Each pick’s label names the need it fits best. The score weighs all four criteria, so a labeled pick can score below another pick.
Prices change often. The comparison table and buttons show the prices we saw on Amazon in October 2026.
Frequently Asked Questions
What is a threshold ramp?
A short ramp, usually 8 to 36 inches long, that bridges a small rise at a doorway, sliding-door track or raised landing so a wheelchair, scooter or rollator can roll over it. Most cover rises of 1/2 inch to about 6 inches.
Does a threshold ramp have to meet ADA rules at home?
No. The ADA’s ramp rules cover public and commercial buildings, and the Department of Justice’s guidance says title III “does not apply to strictly residential facilities” (ADA Title III Technical Assistance Manual). The ADA’s 1:12 maximum slope is still a useful target at home, though few threshold ramps meet it.
What size threshold ramp do I need?
The size that matches your rise. Measure straight down from the top of the threshold to the lower floor, at the highest point across the doorway, and buy that rise. For rises above about 6 inches, use a portable ramp instead.
Can I use a threshold ramp with a rollator or walker?
Yes, if your rollator’s maker allows the slope. The ramp spares you from lifting the front wheels over a lip, but every ramp here is steeper than 1:12, so check your rollator’s manual for the slope it allows and ask your physical therapist if you are unsure.
How much does a threshold ramp cost?
The five ramps in this guide ranged from about $40 to $195 on Amazon in October 2026. Small rubber ramps for a 1 inch lip cost the least; long aluminum ramps with adjustable feet cost the most.